Lateral joints are machined from a forged piece of stainless steel, and are used as flow diversion on pipe lines for the chemical process industry.
Design:
Pressure = 960 PSIG
Test Pressure = 1440 PSIG
Temperature = 302ºF
Sizes:
1 1/2′ x 3/4′
3′ x 2′
4′ x 3′
Do you see a need for lateral joints in your piping system? Get a price quote today!
The personnel protection shields are used when insulating the line is not necessary, but operating temperatures require safeguarding personnel from coming into contact with the pipe. These shields are designed for 8″ pipe operating at 800°F, and are made of 304 stainless expanded steel rolled to a 20″ diameter.
Do you see a need for personnel protection shields in your piping system? Get pricing!
Piping Technology and Products, Inc. and SWECO Fab, Inc. designed and fabricated 24″ 300 # (ANSI rating), 2 1/2″ thick and 42″ 600 # (ANSI rating), 3 7/8″ thick carbon steel spectacle blinds. Spectacle blinds serve the same purpose as flow control valves at less the cost. Spectacle blinds either stop or continue the flow depending on which end is being utilized. PT&P/SWECO Fab. can supply these spectacle blinds in any material needed, such as stainless steel, Monel, Inconel and carbon steel. Smooth, mill, machined or serrated finish is also available upon request. PT&P/SWECO Fab. can produce this product in small quantities/sizes in 48 hours if needed.
Want to learn more about spectacle blinds? Instantly view a Sweco Fab webinar now!
58″ Floating Rings
– Sizes Range from 19″ I.D. to 91 1/2″ I.D.
– ASTM A-240 Grade 316H Stainless Steel
– 100% Dye Penetrant Tested on all Weld Seams
Do you have a requirement for floating rings in your piping system? Get pricing today!
Structural Supports fabricated for an aluminum smelter plant located in Iceland
– Designed to support a process piping system
– Process piping is secured by u-bolts to the slotted supports
– Three coat paint system applied
Do you have a need for structural supports in your current project? Get pricing today!
– 24″ Diameter Horizontal Pressure Vessel
– Repaired Welds on Flange & Shell
– 12 hr. Turn Around Time
– Hydro-Tested at 1500 PSI
– Held for 1 hr. at 80˚F
– 100% X-Ray
Do you require a pressure vessel or tank for your application? Get pricing today!
These pig launchers were manufactured from carbon steel. They have a 16 major barrel, 12 minor barrel and measured 121 long. The pig launchers and receivers are used for cleaning piping systems. In addition, the pig launchers and receivers were designed for pressures of 512 PSIG at 100F. Hydro-tests were performed at 666 PSIG and x-ray tests were completed to ensure quality performance.
Do you require pig launchers or receivers in your piping system? Get pricing today!
This pressure vessel is manufactured from carbon steel SA516-70. Its diameter is 48 by 96 tangent to tangent and weighs 2,140 lbs. The pressure vessel is used as a process feed tank and was painted for rust resistance. In addition, the vessel was designed for pressures at 15 PSIG and temperatures at 86F. Hydro-tests were conducted at 20 PSIG and x-ray tests were completed to ensure quality performance.
Do you require a tank or vessel for your current job? Get pricing now!
These air stacks were designed for 25 PSIG and 100F. They were fabricated from A106-B carbon steel. They are 20 in diameter x 624 long. Each stack weighs 4,395 lb. To ensure product quality, the Inlet Air Stacks were galvanized externally and internally.
Do you have a need for air stacks like those described above? Get pricing today!
Sweco Fab, Inc. recently fabricated an Air Receiver Tank for a Manufacturing Facility in Alabama. This 5,400 lbs tank measured 60″ 143″ tangent to tangent and was designed for 170 PSIG and 200 F. It was fabricated from SA516-70 carbon steel. The interior and exterior were painted with standard epoxy paint to provide an interior lining and exterior protection. The tank was hydrotested at 221 PSIG to ensure product quality.
Want to learn more about products from Sweco Fab? View a past webinar today!
