Structural Supports fabricated for an aluminum smelter plant located in Iceland
– Designed to support a process piping system
– Process piping is secured by u-bolts to the slotted supports
– Three coat paint system applied
Do you have a need for structural supports in your current project? Get pricing today!
Piping Technology & Products, Inc. Designed and Fabricated a Upthrust U-Type Constant for an Energy Plant in California
– Designed for a constant load of 7,733 lb.
– Travel ability is from 0 to 9 inches of total travel
– The constant’s shipping and installation setup is for downward travel
– The constant spring support has been custom designed to reduce its take-off from 36 7/8″ to 29 1/2″
Do you have a need for u-type constants in your plant? Get pricing today!
This particular 24″ pipe shoe was specially designed and fabricated during a planned plant outage. Instead of the normal delivery time of 3-4 weeks, Piping Technology & Products, Inc. finished this project in just one week. This pipe shoe with clamps was designed for 12,900 lb. vertical and 3,000 lb. lateral load. This 1″ thick carbon steel pipe shoe was designed to handle 650°F and has a PTFE, 25% glass filled, slide plate installed to allow for axial movement.
Do you require pipe shoes with clamps like those described above? Get pricing today!
Piping Technology & Products, Inc. Designed and Fabricated Structural Pipe Hangers with Megalug® Pipe Attachments.
These are carbon steel structural supports designed for 6″, 10″ and 12″ ductile iron pipe. They are hot dip galvanized to protect against corrosion and will be used in conjunction with hydraulic snubbers. The hydraulic snubbers are used to protect against axial shock loading, as well as providing vertical weight support.
Each support utilizes a Megalug pipe attachment to eliminate the need for field welding. The Megalug® attachments are designed to “bite” into the sides of the pipe providing an attachment point for the flanges on the fabricated clamp.
The 6″ supports are designed for a maximum vertical load of 3,770 pounds, while the 10″ and 12″ supports are designed for a maximum vertical load of 11,630 pounds. All of the supports are built for an overall height of 55-1/8″ from the upper support steel to pipe centerline.
Want to learn more about our structural supports we offer? Watch a webinar today!
Normal pipeline insulation is not designed to support the pipe or its contents. When insulated pipes are supported, the weight of the pipe, the contents, the operating temperature, and the amount of energy loss must be considered. In order to support the pipe and minimize energy loss from heat transfer, a pre-insulated pipe support is necessary. If the material in the pipe is high temperature such as high pressure steam or heating oil, then high temperature insulation is required, and these supports are called hot shoes. If the material is cold, such as liquefied natural gas, cooling water or ammonia, then low temperature insulation is needed, and these types of supports are called cold shoes.
PT&P received the order to fabricate 140 cold shoes from a contractor in Puerto Rico. The overall weight of the order was 11,000 lbs and was produced in 8 weeks. The shoes were designed to support 8, 10 and 12 inch pipe sizes with 2 inches of insulation. They were designed using our Pipe Shields Division and correspond to the following model numbers: B2000, B4000,and C4100. These can be seen on our Pipe Shields website or you can request a catalog.
Want to learn more about cold shoes? Watch one of our cold shoe webinars today!
– 24″ Diameter Horizontal Pressure Vessel
– Repaired Welds on Flange & Shell
– 12 hr. Turn Around Time
– Hydro-Tested at 1500 PSI
– Held for 1 hr. at 80˚F
– 100% X-Ray
Do you require a pressure vessel or tank for your application? Get pricing today!
The limiting constraint in designing and fabricating these big ton spring supports was to maintain an overall height less than 15-3/4″ and still allow the load table to travel downward during operation. Whereas a standard PT&P size 2-190 variable springs would have been sufficient to hold the load specified, the coil alone was taller than the space available at site. For this reason, a “big ton” design was implemented which utilized six smaller coils (2-130 size) working in parallel to produce the required load-carrying capability and spring rate.
All of the frame/housing components were made from carbon steel and supplied with an HDG finish. The travel stop rods were made of A-193 Gr. B7 material and were painted red. The slide plates sitting atop the load flange were made of polished A-304 stainless steel.
Both “big ton” assemblies are 30″ wide by 30″ deep by 15-3/4″ tall. Overall spring rate is 3,600 lb/in. and each weighed approximately 1,460 pounds. The installed (cold) load = 14,800 lbs. and the operating (hot) load = 16,075 lbs. Movement from cold to hot = 0.354″ down.
Tested in the load cell to insure proper operation throughout the entire working range of the coils, the “big tons” were then set to the cold (installed) load as specified.
Want to learn more about big ton springs? Watch one of our engineered spring webinars now!
Piping Technology & Products, Inc. custom fabricated sixty bolt cradle supports in May 2006. The base was fabricated by welding two plates to form a “T.” This was used in place of a standard split “T.” By making simple modifications to a standard Figure 900 for two-inch pipe, such as heavier clamps and shortened base length, PT&P was able to meet the customer’s special requirements quickly and efficiently.
Do you require cradle supports for your current or future job? Get pricing today!
200-U Type Constant-Custom Design
– Designed for 21,269 lb. load
– 26-1/4″ W x 80″ L x 28-1/2″ H
– 10″ upward travel
– 12″ total travel
200-U Type Constant
– Designed for 18,273 lb. load
– 26-3/8″ W x 66″ L x 23-1/4″ H
– 0.43″ downward & 1.22″ upward travel
– 3″ total travel
100-G Type Constant
– Load range: 15,226 lb. to 17,210 lb
– 13″ W x 87″ L x 59″ H
– 2.8″ downward travel
– 4″ total travel
200-U Type Constant-Custom Design
– Load Range: 14,060 lb. to 18,334 lb.
– 27″ W x 84″ L x 24-5/8″ H
– Actual Travel Range: 10″ to 11″ Upward
– Total Travel Range: 12-1/2″ to 13-1/2″
Do you see a need for constant spring supports in your plant? Get pricing today!
Piping Technology and Products, Inc. received an order for a power plant in Argentina from our Pipe Shields division. This order consisted of variable assemblies, constant support assemblies, sway struts, and pre insulated pipe supports. Pipe sizes supported were up to 42” with 3” of insulation ranging from 340 lb. to 1300 lb. All hot shoes were designed to carry the load, along with its own weight and insulation. Since these pre-insulated supports are used for high temperature pipes, PT&P used calcium silicate as insulation and hot dipped galvanized the steel as a rust inhibitor. Piping Technology and Products Inc. handled all logistics of the international shipment.
Do you require hot shoes for your plant or refinery? Let us price them for you today!
