Piping Technology & Products, Inc. designed and manufactured carbon steel and alloy stanchions for a power center in Arizona. PT&P also produced carbon steel beams for the project.
These stanchions are made to fit Extra Strong and Standard pipes, which are 3-12 in size. Figure 1 shows the stanchions and beams for this job before they were coated with a green primer and prepared for shipment.
Do you see a need for stanchions and beams in your power plant or refinery? Get pricing today!
Piping Technology & Products, Inc. designed and manufactured 250 variable sized cold shoes for a chemical plant in Texas.
These cold shoes are designed for cryogenic (low temperature) pipelines where direct contact with the pipe cannot be made. These shoes come with two pieces, top and bottom, and are made of polyurethane foam. They are then wrapped in vapor barriers, covered with a protective shield and placed in a pipe saddle.
Want to learn more about cold shoes? View a pre-insulated pipe support webinar today!
Piping Technology & Products, Inc. designed and manufactured variable spring supports for a refinery in Forney, Texas.
The spring supports are made of carbon steel and have a length by casing diameter range from 9-3/16 by 8-5/8 to 53-11/16 by 12 ¾. In order to insure the quality of the springs, compression tests were used with a load capacity of 21,500 pounds.
Need supports like these? Let us help serve your needs!
Sweco Fab, Inc. designed and manufactured pig launchers and receivers for an oil and gas exploration and production company in Venezuela.
The launchers and receivers are designed with a 6 line and 8 barrel at 60 long with a 4 kicker, ¾ in. P.I., 2 vent and drain design per ASME B31.4. They are made to withstand 1480 PSIG at 100ºF and can accommodate 15 pigs. They were painted inside and out per System 6E grey color and included simple skid, MTR, N.D.E., and flange protectors.
Learn about these products and more from our webinar archives!
Piping Technology & Products, Inc. designed and manufactured PTFE, 25% glass filled, slide plates for a chemical plant in Port Arthur, Texas.
These slide plates are constructed of PTFE, 25% glass filled, bonded to stainless steel backing plates. The top plates range from 123 ¾ square inches to 481 ¾ square inches and the bottom plates range from 69 square inches to 616 square inches.
Want to find out more information about slide plates? Visit our webinar archives today!
Piping Technology & Products, Inc. designed and manufactured saddles for a power project in California.
The saddles were built for 12″, 24″ and 30″ pipe and the loads varied from 1,500 pounds to a maximum design load of 20,000 pounds. The saddle and its components will hang from a beam in the field by spring hangers to complete what is known as a “trapeze” pipe hanger assembly. In order to prevent movement, the supported pipes will be secured to the curved portion of the saddle with u-bolts.
If you are in need of pipe saddles, let us know! We would be glad to help you.
Piping Technology & Products, Inc. specially designed and fabricated big ton springs equipped with special rollers to accommodate moving apparatus and support piping at a refinery in India.
The specially designed big tons were made to support loads ranging from 55,000 lbs. to 114,000 lbs with no more than 5/16″ upward movement. Its composition comprises of A-36 carbon steel, built to a maximum height of 23-5/8″.
The special rollers installed on the top of the load flange, keeps the aforementioned loads moving smoothly under all kinds of conditions. To further assure their quality, each of the big ton spring assemblies underwent load testing and afterward were hot dipped galvanized to prevent against corrosion.
Want to learn more about big tons? Visit our webinar archives today!
Sweco Fab, Inc. recently designed and manufactured sludge tank vent ducts for a development project in Chad, Africa.
Due to the thin wall and height of the cylinder shell it was required to add a stiffing ring between the cylinder shell and flange. Each duct was 12 ¼” I.D. x 104 7/8″ high and weighed approximately 96 pounds. They were painted inside and out per System 6E grey color.
Learn more about Sweco Fab, Inc. and it’s products by visiting our webinar archives today!
Piping Technology & Products manufactured 2″ hold down clamps (figure HD-1) for an engineering and construction company.
The figure HD-1 is PT&P’s anchor type hold down and is usually used on pipe lines where little or no insulation is required. These hold down clamps were constructed of SA36 carbon steel for temperatures to 750ºF.
Need hold down clamps? We’re happy to serve your needs!
Piping Technology & Products custom designed and manufactured vertical F-type constants for a power plant in Connecticut.
The 100 type F is a vertical constant designed to support piping from below with minimum space usage. The dimensions of the constant are 26-5/8″ high, 10″ wide, and 17-9/16″ long with an operating load of 280 lbs.
This particular F constant, was unusual in that it was furnished with a vertical spring that attaches below the frame of the constant. In addition to a downward travel of 3″, the flange table shifts forward at 1-3/8″ to minimize axial movement.
A galvanized finish was applied to the constant to prevent corrosion. The constants can be bolted on or welded to the support or steel underneath.
Need constants for an upcoming project? Ask for pricing today!
