78 Heavy Duty Pipe Saddles for Insulated Ductile Iron PipelinesSide View of Pipe Saddles
PT&P custom designed seventy-eight figure 2000 heavy duty pipe saddles for two 24″ insulated ductile iron pipelines. The two pipelines are routed beneath a 650′ bridge crossing over a river in upper New York State. The insulation is 3″ thick with high density polyethylene jacketing. Axial movements due to expansion can approach 3″. In order for the jacketing to avoid being damaged when displacements occur, the saddles have been lined with polished stainless steel.
Would you like to order similar pipe saddles for your current or future job? Get pricing!
This custom pipe clamp will be used in conjunction with a hydraulic snubber to restrain pipe movement during extremely high disturbances. It is designed to support the pipe where two heavy duty flanges join. The yoke, lugs, and strap sections of the clamp are carbon steel, and the clamp bolts and load bolt/pin are stainless steel.
The outer diameter of the clamp section is 16″, and the inner diameter is 10″. The upper lugs are fabricated from 3/4″ thick plate with a 2-1/4″ diameter load bolt. The maximum load for this custom clamp is 68,000 lb.
Do you require custom pipe clamps in your piping system? Get pricing today!
10″ Beam Clamp Assemblies for an Electric Plant in West VirginiaBeam Clamp
These beam clamp assemblies are fabricated from carbon steel with a hot-dipped galvanized finish. The clamp is designed to support a pipe that is 10″ in diameter and is capable of loads up to 3,600 lb. The rod measures 7/8″ in diameter.
The function of the beam clamp assembly is to support the pipe and allow it to swing. The clamp requires no welding which allows for a quick and easy installation.
Do you require beam clamp assemblies in your project? Get pricing today!
97" Diameter, 3-Piece Pipe Clamps for a Refinery in Ponca City
Piping Technology & Products, Inc. fabricated 3-piece pipe clamps used to support 97″ diameter stainless steel duct work. This duct work is being added to a refinery for an expansion project in Ponca City, Oklahoma. Each section of the clamp assembly is formed from a continuous plate and gussets are added at each of the bolt locations for increased strength and rigidity. Due to the ducts having a relatively thin wall, these clamps are designed wider than necessary in an effort to reduce localized stresses on the duct work. The lower section of each clamp is formed to create a 150° cradle. This acts as a cradle by supporting the duct without inducing extra pressure, which might cause the duct wall to buckle or bend.
The upper sections are formed from 1/2″ thick by 12″ wide bar stock, whereas the lower sections are formed from 1/2″ thick by 18″ wide. All three sections are rolled to an inner radius of 48 1/2″ and the welded gusset plates are all 1/2″ thick. The upper sections are formed at 105° each, and the upper load bolt is 2″ in diameter while the six clamping bolts are 1 1/2″ in diameter.
The maximum load to be carried by these pipe clamps is 16,888 lb. Each pipe clamp will be used in conjunction with a variable spring support to accommodate movements as high as 2 1/4″.
Do you require 3-piece pipe clamps for your plant or refinery? Get pricing now!
42" Large Bore Pipe Saddles42" Large Bore Pipe Saddles42" Large Bore Pipe Saddles
PT&P fabricated 42″ diameter large bore pipe saddles. All pipe saddles are designed to be used on flare lines for a crude expansion project. They are fabricated from A-36 carbon steel and hot dipped galvanized. Sizes range from 16″ – 48″ in diameter and 6″ – 15″ in height.
Do you require large bore pipe saddles in your current project? Get pricing today!
Piping Technology & Products, Inc. designed and fabricated pipe saddles for 42″ pipe size. The maximum vertical load is 27,649 lb., axial load is 5,500 lb. and lateral load is 6,040 lb.
Do you see a need for pipe saddles like the one described above? Get pricing today!
Riser Clamps for a Power Plant in Rhode IslandRiser Clamp
Piping Technology & Products designed and fabricated 80,000 lb. capacity, Type-3 riser clamps for a power plant in Rhode Island. These riser clamps are designed for a 16″ pipe with 2″ flanges for added support.
Do you see a need for riser clamps in your piping system? Let us price them for you!
Structural Supports with Megalug Pipe AttachmentsMegalug AttachmentsMegalug Pipe Attachments
Piping Technology & Products, Inc. Designed and Fabricated Structural Pipe Hangers with Megalug® Pipe Attachments.
Structural Supports with Megalug Pipe Attachments
These are carbon steel structural supports designed for 6″, 10″ and 12″ ductile iron pipe. They are hot dip galvanized to protect against corrosion and will be used in conjunction with hydraulic snubbers. The hydraulic snubbers are used to protect against axial shock loading, as well as providing vertical weight support.
Each support utilizes a Megalug pipe attachment to eliminate the need for field welding. The Megalug® attachments are designed to “bite” into the sides of the pipe providing an attachment point for the flanges on the fabricated clamp.
Structural Supports
The 6″ supports are designed for a maximum vertical load of 3,770 pounds, while the 10″ and 12″ supports are designed for a maximum vertical load of 11,630 pounds. All of the supports are built for an overall height of 55-1/8″ from the upper support steel to pipe centerline.
Want to learn more about our structural supports we offer? Watch a webinar today!
80ft. wide Cantilevered Canopy for an International Project
Piping Technology & Products, Inc. fabricated a Cantilevered Canopy for the entrance of an International State Department building. The Canopy was fabricated using ten 20-foot long girders. These girders were connected by sixty-three structural steel members. Together, they formed the 80-foot width of the Canopy. The wooden sheathing and architectural cladding that is supported by the canopy’s inner steel structure was installed at the construction site.
The fabricated girders and structural members combined weight exceeds 33,000 lb.
Piping Technology & Products also supplied the steel framing that supports the sheathing and cladding, roof drains and piping installed inside the canopy.
Want to learn more about the miscellaneous structures we provide? Watch a webinar today!
Structural Pipe Hangers for a Pipe Seismic Restraint ProjectClose-Up View of MegaLug
Piping Technology & Products, Inc. and its wholly owned subsidiary, Pipe Shields, Inc. designed and fabricated many structural pipe hangers for an on-going project to rebuild the San Francisco-Oakland Bay Bridge. The pipe hangers are made out of A-36 carbon steel and galvanized to withstand corrosion from the ocean waters and rough winds. These pipe supports will be welded to Pipe Shields’ C Model Anchor Plates, which are set in a cast concrete to the bottom cavity of the bridge.
Structural Pipe Hangers
Supports pictured utilize friction holding devices known as MegaLug®, which permit attachment to the pipes without welding. These supports were designed and fabricated to include improvements in regard to strength and durability to withstand high loads during earthquakes and other seismic events.
Do you see a need for structural pipe hangers in your application? Get pricing now!
We use cookies on our website to give you the most relevant experience by remembering your preferences and repeat visits. By clicking “Accept”, you consent to the use of ALL the cookies.
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. These cookies ensure basic functionalities and security features of the website, anonymously.
Cookie
Duration
Description
cookielawinfo-checkbox-analytics
11 months
This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Analytics".
cookielawinfo-checkbox-functional
11 months
The cookie is set by GDPR cookie consent to record the user consent for the cookies in the category "Functional".
cookielawinfo-checkbox-necessary
11 months
This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary".
cookielawinfo-checkbox-others
11 months
This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Other.
cookielawinfo-checkbox-performance
11 months
This cookie is set by GDPR Cookie Consent plugin. The cookie is used to store the user consent for the cookies in the category "Performance".
viewed_cookie_policy
11 months
The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. It does not store any personal data.
Functional cookies help to perform certain functionalities like sharing the content of the website on social media platforms, collect feedbacks, and other third-party features.
Performance cookies are used to understand and analyze the key performance indexes of the website which helps in delivering a better user experience for the visitors.
Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics the number of visitors, bounce rate, traffic source, etc.
Advertisement cookies are used to provide visitors with relevant ads and marketing campaigns. These cookies track visitors across websites and collect information to provide customized ads.
