Piping Technology & Products, Inc. recently designed and manufactured two strap assemblies for a chemical plant in Texas.
These 24′ x 8 straps are comprised of A516-70 plates, struts, pipe clamps, SCHXS and SCH160 pipe, and fabricated turnbuckles. This job was completed within two weeks to meet the customer’s quick turnaround requirements.
Do you require pipe straps in your piping system? Get pricing today!
Piping Technology & Products, Inc. designed and manufactured carbon steel and alloy stanchions for a power center in Arizona. PT&P also produced carbon steel beams for the project.
These stanchions are made to fit Extra Strong and Standard pipes, which are 3-12 in size. Figure 1 shows the stanchions and beams for this job before they were coated with a green primer and prepared for shipment.
Do you see a need for stanchions and beams in your power plant or refinery? Get pricing today!
Piping Technology & Products, Inc. designed and manufactured saddles for a power project in California.
The saddles were built for 12″, 24″ and 30″ pipe and the loads varied from 1,500 pounds to a maximum design load of 20,000 pounds. The saddle and its components will hang from a beam in the field by spring hangers to complete what is known as a “trapeze” pipe hanger assembly. In order to prevent movement, the supported pipes will be secured to the curved portion of the saddle with u-bolts.
If you are in need of pipe saddles, let us know! We would be glad to help you.
Piping Technology & Products manufactured 2″ hold down clamps (figure HD-1) for an engineering and construction company.
The figure HD-1 is PT&P’s anchor type hold down and is usually used on pipe lines where little or no insulation is required. These hold down clamps were constructed of SA36 carbon steel for temperatures to 750ºF.
Need hold down clamps? We’re happy to serve your needs!
Piping Technology & Products, Inc. designed and manufactured hundreds of hanger rods and clevises for a 1,250 MW natural gas combined cycle facility in Mississippi.
The rod and clevis components were made of various alloys (800H, F91, 316H, SA-387 Gr. 22) and ranged in sizes from 2″ to 4″ diameter. Taking into account the surrounding environment’s conditions, engineers designed the rods and clevises so that they can endure temperatures escalating to 1430º F. For the duration of a pull test conducted, the clevises and rods sustained loads up to 152,000 lbs. and there were no discrepancies.
Are rods and clevises on your checklist for an upcoming project? Request a quote today!
The clamp attachments shown are used for supporting vertical pipe sections to vessel clip anchors. These braces are designed for a maximum horizontal moment of 15,000 ft-lb at the vessel clip. All the clamps provided were made of carbon steel with a hot-dip-galvanized finish. The pipe hanger assembly lengths were fabricated per specifications provided by the client.
The clamp components were designed and fabricated for non-standard pipe diameters (i.e. 13-3/4″, 16-1/2″) so that they could be used on insulated or finned pipelines.
Are you in need of clamp attachments? Request a quote today and receive a response within 48 hours!
Piping Technology & Products, Inc. designed and fabricated 24″, chrome-moly, three-bolt clamps with horizontal guide stanchions for a 765 MW natural gas-fired combined cycle facility in Mexico.
These clamps, in conjunction with variable springs, will allow for vertical and axial pipe movement while restricting lateral movements. They were made for 24″ OD pipe from 1-1/2 x 9″ stock material. Based upon design considerations, the clamp “E” dimension, from pipe centerline to outer load bolt, was 25″. The clamps were designed for operation at 1065°F and per customer-supplied information, the vertical design load was 1,848 lbs and the maximum lateral load was 19,207 lbs.
The clamp plates are made of A387 GR. 22 plate material, stanchion pieces of A335 GR.22 pipe and the side stop plates of carbon steel.
Want more information on three-bolt clamps? Learn more about them in our webinar archives!
PT&P Utilizes 3D-Modeling Technology to Design Pipe Supports for a 750MW Power Plant
Piping Technology & Products, Inc. recently designed and fabricated 9 pipe supports with loads up to 75,000 lbs. for a 750MW power plant in Alabama. After extensive engineering hours and structure analysis, PT&P’s engineering department produced a detailed design and 3-D model for the supports that would allow them to run electronic interface checks. The supports are to support the cooling towers’ circulatory water system at the power plant. Six of the 9 supports were designed for a 60” line and 50,000 lb. load, and the remaining 3 were designed for a 78” line and 75,000 lbs. of load.
Furnace Springs Versus Standard Springs The major differences between standard springs and furnace springs are their construction and intended use. Furnace springs operate in much the same way as other variable spring supports. They are designed to support the pipe and tubes that are subject to vertical thermal movement. The design changes come about because, furnace springs are exposed to extreme temperatures.
|
Piping Technology & Products, Inc. custom designed and fabricated a 66-inch diameter, three-bolt pipe clamp for a chemical company located in Deer Park, Texas.
The clamp will be used in conjunction with a PT&P Spring Hanger and a length of rod in order to support the pipeline. After formation, the clamp’s dimensions measured at 97.75 OAL and 69.5 at its widest point. By using a FEA program, the clamp was designed for an operating load of 24,000 pounds at 500° F. The materials used consisted of 1 ¾ x 10 x 128 ¼ thick A-36 Carbon steel, with three 2½ studs and nuts.
In need of some three-bolt pipe clamps? Request for pricing today!
Piping Technology & Products, Inc. custom designed and fabricated 1,728 rods and clevises for a heat recovery steam generation plant. The rods and clevises will be utilized to support various pipe loads throughout the piping system.
Learn more about rods and clevises by visiting our webinar archives!
